Industry · construction & water
Grade C's natural home, and nobody should pay more.
01 / WHAT THIS SECTOR NEEDS
Tough, cheap and delivered to a site with no dock
Almost all construction duty is non-potable water service: hose fill for concrete work, dust suppression, compaction water, hydro-seeding, tool washing and temporary storage. For all of that a Grade C unit — stained, scored, sound — is the correct purchase. It holds water perfectly and costs a fraction of a Grade A.
The second constraint is delivery. Jobsites rarely have a dock. We run a box truck with a lift-gate for up to sixteen units, which costs more per unit than a flatbed and is the only thing that actually works on a muddy site entrance. Tell us the access situation in the form and we will quote the right equipment rather than discovering the problem at your gate.
Common construction duty
- Jobsite water storage and hose fill
- Dust suppression, with or without a pump skid
- Concrete admixtures and curing compounds
- Tool and boot wash stations
- Temporary secondary containment
- Hydro-seeding and erosion control slurry
Where to be careful
Freezing. A full tote left out in an Indiana January will split, and HDPE gets brittle below about -20 °F so handling damage goes up too. Drain below half, or specify a frost-break drain plug on an upcycled build.
Typical specification
- Capacity275 gal
- GradeC
- Seat materialEPDM
- PalletSteel — site abuse
- LidVented
- OutletS60x6 + garden hose adapter
- DeliveryLift-gate box truck
- Common extrasFoot pump, spray bar, stand
The trap we see most
Using a tote for potable water on the basis that it looks clean. Grade C units are not potable containers and we do not sell them as such. If a crew needs drinking water, that is a different product with a documented food history — and we will tell you that every time you ask.
“The jobsite wash station was a customer's idea. He drew a foot pump and a soap shelf on the back of a delivery ticket. We have built four hundred of them since.”Walt Krzeminski · Fabrication, ToteOrbit
02 / BUILDS
From the upcycle bay
Three site builds we make constantly
Wash station
Tote on a cage stand with a foot-pump tap, soap shelf and greywater catch tray. Forkliftable, no power required.
Dust suppression skid
Tote, 12 V pump, spray bar and battery box on a skid base. Runs off a truck battery or a small solar panel.
Containment berm frame
Stripped cages bolted into a rectangular frame and lined. Cheap secondary containment built entirely from scrap steel.
C / COMPATIBILITY
Will HDPE hold it?
Sixteen cargo families, rated
| Cargo family | HDPE | Seat | Notes |
|---|---|---|---|
| Water, potable and non-potable | A | EPDM / silicone | Food-history units for potable |
| Acids and caustics, aqueous | A | EPDM / PTFE | Vent fuming cargo |
| Liquid fertiliser, UAN, NPK | A | EPDM | SG up to 1.32 — check your lift-gate |
| Brine and chloride de-icer | A | EPDM | Hard on galvanising, kind to HDPE |
| Food syrups, oils, concentrates | A | Silicone / Viton | Documented food history only |
| Glycols | A | EPDM | Very common; SG 1.04–1.11 |
| Alcohols | A | Viton / PTFE | Flammable — bond and vent |
| Diesel and gas oil | B | Viton / NBR | Permeates slowly over long storage |
| Mineral spirits | B | Viton | Swells HDPE slowly |
| Surfactants and detergents | B | EPDM | Odour fixation risk — dedicate units |
| Latex, adhesives, water-based paint | A | EPDM | Cures if left. Wash promptly. |
| Ketones, aromatics, chlorinated solvents | C | — | Crazes HDPE. Stainless only. |
| Gasoline and low-conductivity fuels | C | — | Static risk. Steel or stainless. |
| Essential oils, flavour concentrates | C | — | Fixes into the wall permanently. Never. |
| Hydrogen peroxide above 10% | C | — | Decomposition and pressure risk |
| Dairy and hot-fill above 140 °F | C | — | Needs CIP and steam. Stainless. |
Permeation
Small non-polar molecules pass slowly through HDPE rather than attacking it. The bottle looks perfect and your cargo quietly leaves. It is a storage-duration problem: diesel for a week is fine, diesel for a year is not.
Crazing
Ketones, aromatics and chlorinated solvents cause fine surface cracking that propagates under stress. It is invisible until you hold the wall against a raking light, and it is a critical grading failure.
Odour fixation
Terpenes and some surfactants dissolve into the polymer itself rather than sitting on the surface. No wash removes them. This is why a food-grade tote has to have been a food tote from new.
A / SPECIFICATION
Reference
Dimensions, fittings and seat materials
Fig. 1
Fig. 2| Capacity | Litres | Footprint | Height | Tare | Gross (water) | Stack loaded |
|---|---|---|---|---|---|---|
| 275 gal | 1,041 | 48 × 40 in | 46 in | ≈140 lb | ≈2,435 lb | 2 high |
| 330 gal | 1,249 | 48 × 40 in | 53 in | ≈155 lb | ≈2,905 lb | 2 high |
| 350 gal | 1,325 | 48 × 40 in | 56 in | ≈165 lb | ≈3,075 lb | 2 high |
| 120 gal | 454 | 40 × 32 in | 38 in | ≈95 lb | ≈1,095 lb | 2 high |
| 180 gal | 681 | 42 × 36 in | 42 in | ≈115 lb | ≈1,616 lb | 2 high |
| 550 gal | 2,082 | 60 × 48 in | 60 in | ≈240 lb | ≈4,830 lb | 1 high |
B / FITTINGS
What threads onto it
Fittings, threads and seat materials
| Fitting | Size | Seals by | Seat options | Typical service |
|---|---|---|---|---|
| S60x6 butterfly valve | 2 in | Flat gasket face | EPDM, Viton, PTFE | The standard IBC outlet |
| S70x6 butterfly valve | 2 in | Flat gasket face | EPDM, Viton | European and some 330 gal units |
| 2 in NPT ball valve, poly | 2 in | Thread flanks + tape | EPDM, Viton | Retrofits, metered dispensing |
| 2 in NPT ball valve, stainless | 2 in | Thread flanks + tape | PTFE | Solvents, pressure, hot cargo |
| 3 in butterfly valve | 3 in | Flat gasket face | EPDM, Viton | Viscous cargo, high flow |
| 6 in fill cap | 6 in | Gasketed lid | EPDM, silicone | Vented or solid — choose deliberately |
| Camlock adapter, type C | 1.5 / 2 in | Cam arms + gasket | Buna, Viton | Repeated connect / disconnect |
| Bulkhead tap | 3/4 in | Both-side gaskets | Brass, poly | Rain kits, site water |
| Material | Good with | Avoid with | Temperature | Cost |
|---|---|---|---|---|
| EPDM | Water, acids, caustics, brine, ag-chem | Oils, fuels, aromatics | -40 to 250 °F | Low |
| Viton (FKM) | Solvents, oils, fuels, aromatics | Ketones, amines, hot steam | -15 to 400 °F | High |
| Nitrile (NBR) | Oils, diesel, greases, hydraulics | Ozone, strong oxidisers | -30 to 250 °F | Low |
| PTFE envelope | Almost all chemistry, high purity | Needs very flat flange faces | -100 to 450 °F | High |
| Silicone | Food contact, wide temperature | Solvents, abrasion | -60 to 450 °F | Medium |
E / GRADING
A grade is a promise, not a mood
How every unit is scored
| # | Point | Critical? |
|---|---|---|
| 01 | Prior cargo declaration — present, written, specific | Yes |
| 02 | Residual liquid — any volume at all | Yes |
| 03 | Odour after wash — fixed odour by trained nose | Yes |
| 04 | Bottle corner stress whitening | No |
| 05 | Interior scoring you can feel | No |
| 06 | Interior crazing — fine surface cracking | Yes |
| 07 | Bottle bulge or deformation | Yes |
| 08 | Wall thickness at the thinnest point | Yes |
| 09 | Dome port condition and flange flatness | No |
| 10 | Outlet threads — cross-threading, chipping | Yes if crossed |
| 11 | Valve function, full open and close | No, replaceable |
| 12 | Gasket condition — compression set, bloom | No, replaceable |
| 13 | Cage squareness along the top rail | No, pressable |
| 14 | Cage weld integrity at tube intersections | Yes |
| 15 | Cage coating and galvanising loss | No |
| 16 | Pallet condition — cracked feet, rot, corrosion | No, replaceable |
| 17 | Forklift pocket integrity | No |
| 18 | UN marking legibility and date | No, re-markable |
| 19 | Leak test under our procedure | Yes |
D / ORDERING
Commercial terms, up front
Lead times, minimums and what happens when it goes wrong
| Item | Detail |
|---|---|
| Minimum order | One unit. No account minimum, no membership. |
| Stock lead time | Grade A and B 275 gal usually ship the same week |
| Rebottled lead time | 2–3 weeks, built to order in bay D |
| Food-grade lead time | 1–3 weeks when stock exists; supply-dependent |
| Full truckload | 45 on a 48 ft flat, 48 in a 53 ft van, 90 empties double-stacked |
| Payment, first order | Prepay by ACH or card |
| Payment, established | Net 30 on credit approval |
| Grade guarantee | Regrade or replace, our freight both ways, 14 days |
| Leak warranty | 30 days from delivery, normal atmospheric service |
| Cancellation | Free until the truck is loaded |
| Returns | 14 days on unused stock units, freight at your cost |
| Sales tax | Indiana resale certificates and out-of-state equivalents accepted |
G / PITFALLS
Learned the expensive way
Five mistakes that cost people money
Ordering a 330 without measuring the ceiling
A 275 and a 330 share a footprint; the 330 is seven inches taller. Two 330s stacked is 110 inches against 96 for two 275s, and most sprinkler regimes want eighteen inches of clearance below the deflector. That seven inches is frequently the whole margin.
Forcing an NPT fitting into an S60x6 port
Both are roughly two inches, so it bites and feels tight. It is not sealing, it is chewing the buttress thread. The joint weeps two days later, usually in transit, and cross-threading is one of the few faults that condemns an otherwise perfect bottle.
Reusing a flange gasket
A gasket is a one-use part the moment it has taken a compression set. Reusing one is the cause of most 'the new valve still leaks' emails we get. They cost a couple of dollars. Keep a box at the fill point.
Specifying a solid lid on a tote that sees sun
Sealed container, rising temperature, nowhere for the expansion to go. The bottle bulges between the cage bars and does not fully return. A vented lid is the cheapest risk control in this industry.
Ignoring specific gravity
A full 275 of water is 2,435 lb. The same tote of UAN 32 is 3,168 lb, and a 330 is 3,785 lb. Plenty of lift-gates are rated at 2,500 or 3,000 lb, and the rating assumes a centred load.
We will talk you down a grade